View RS5C313_153997.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ULTRA-COMPACT REAL-TIME CLOCK IC
RS5C313
APPLICATION MANUAL
ELECTRONIC DEVICES DIVISION
NO.EA-034-9908
NOTICE
1. The products and the product specifications described in this application manual are subject to change or discontinuation of production without notice for reasons such as improvement. Therefore, before deciding to use the products, please refer to Ricoh sales representatives for the latest information thereon. 2. This application manual may not be copied or otherwise reproduced in whole or in part without prior written consent of Ricoh. 3. Please be sure to take any necessary formalities under relevant laws or regulations before exporting or otherwise taking out of your country the products or the technical information described herein. 4. The technical information described in this application manual shows typical characteristics of and example application circuits for the products. The release of such information is not to be construed as a warranty of or a grant of license under Ricoh's or any third party's intellectual property rights or any other rights. 5. The products listed in this application manual are intended and designed for use as general electronic components in standard applications (office equipment, computer equipment, measuring instruments, consumer electronic products, amusement equipment etc.). Those customers intending to use a product in an application requiring extreme quality and reliability, for example, in a highly specific application where the failure or misoperation of the product could result in human injury or death (aircraft, spacevehicle, nuclear reactor control system, traffic control system, automotive and transportation equipment, combustion equipment, safety devices, life support system etc.) should first contact us. 6. We are making our continuous effort to improve the quality and reliability of our products, but semiconductor products are likely to fail with certain probability. In order prevent any injury to persons or damages to property resulting from such failure, customers should be careful enough to incorporate safety measures in their design, such as redundancy feature, fire-containment feature and fail-safe feature. We do not assume any liability or responsibility for any loss or damage arising from misuse or inappropriate use of the products. 7. Anti-radiation design is not implemented in the products described in this application manual. 8. Please contact Ricoh sales representatives should you have any questions or comments concerning the products or the technical information.
June 1995
RS5C313
APPLICATION MANUAL
CONTENTS
OUTLINE ......................................................................................................1 FEATURES....................................................................................................1 BLOCK DIAGRAM .........................................................................................2 APPLICATIONS .............................................................................................2 PIN CONFIGURATION ...................................................................................2 PIN DESCRIPTIONS ......................................................................................3 ABSOLUTE MAXIMUM RATINGS ...................................................................4 RECOMMENDED OPERATING CONDITIONS .................................................5 DC CHARACTERISTICS ................................................................................5 AC CHARACTERISTICS ................................................................................6 TIMING CHART .............................................................................................6 FUNCTIONAL DESCRIPTIONS ......................................................................7 1) Addressing ...............................................................................................7 2) Registers .................................................................................................8 3) Counters ................................................................................................12 USAGES......................................................................................................14 1) Read Data ..............................................................................................14 2) Write Data ..............................................................................................15 3) CE Pin ..................................................................................................16 4) Configuration of Oscillating Circuit ..................................................................17 5) Oscillator Halt Sensing ................................................................................18 6) Typical Power Supply Circuit .........................................................................18 7) Oscillation Frequency Adjustment ...................................................................19 8) Interrupt Operation ....................................................................................20 9) Typical Application .....................................................................................21 10) Typical Characteristic Measurements ...............................................................22 11) Typical Software-based Operations .................................................................24 PACKAGE DIMENSIONS ..............................................................................28 PACKAGE SPECIFICATION ..........................................................................28
ULTRA-COMPACT REAL-TIME CLOCK IC
RS5C313
OUTLINE
The RS5C313 is a CMOS type real-time clock which is connected to the CPU via three signal lines and capable of serial transmission of clock and calendar data to the CPU. The RS5C313 can generate various interrupt clock pulses lasting for long periods (one month). Driving an oscillation circuit at constant voltage, the circuit undergoes few voltage fluctuations and consequently realizes low current consumption (TYP. 0.7 A at 3 V). It also provides an oscillator halt sensing function for application to data validity at power-on and other occasions. Integrated into an ultra-compact and ultra-thin 8pin SSOP (0.65mm pitch), the RS5C313 is the optimum choice for equipment requiring small size and low power consumption. There is RS5C314 reversing the logic of serial clock for series goods.
FEATURES
* Time Keeping Supply Voltage: 1.6 to 6.0 V * Operating Supply Voltage: 2.7 to 6.0 V * Low Current Consumption: TYP. 0.7A (MAX. of 1.5A) at 3V * Connection to the CPU via only three pins: CE, SCLK, and SIO (for addressing and data read and write operations) * A clock counter (counting hours, minutes, and seconds) and a calendar counter (counting leap years, years, months, days, and days of the week) in binary-coded decimal (BCD) code * Generation of interrupt pulses to the CPU with cycles ranging from 1 month to 1/1024 Hz, interrupt flags, and interrupt halt * Software-based alarming through clock-interlocked interrupt operation * Oscillator halt sensing to judge internal data validity * Second digit adjustment by 30 seconds * 12-hour or 24-hour time display selectable * Automatic leap year recognition up to the year 2099 * CMOS logic * Package: 8pin SSOP (0.65mm pitch)
1
RS5C313
BLOCK DIAGRAM
OSCIN OSCOUT OSC DIV SEC. MIN. HOUR WEEK DAY MONTH YEAR
TIME COUNTER VDD VOLTAGE REGULATOR VSS INTR OSC DETECT SCLK ADDRESS DECODER ADDRESS REGISTER I/O CONTROL CE SHIFT REGISTER SIO
INTERRUPT CONTROL
APPLICATIONS
* Communication equipment (Multi-function telephone, portable telephone, PHS, Pager) * Office automation (Facsimile, portable facsimile) * Personal computer (Desk top type, notebook type, word proccesor, PDA, electronic notebook, TV games) * Audio visual equipment (Portable audio equipment, video camera, camera, digital camera, remote control equipment) * Home use (Rice cooker, microwave range)
PIN CONFIGURATION
* 8pin SSOP
CE SCLK SIO VSS
1 2 3 4
8 7 6 5
VDD OSCIN OSCOUT INTR
2
RS5C313
PIN DESCRIPTIONS
Pin No. Symbol Name Description
1
CE
Chip enable input
The CE pin is used to interface with the CPU and is accessible when held at the high level. This pin incorporates a pull-down resistor. It should be switched to the low level or opened when not accessed or when powering off the system. Holding the CE pin at the high level for more than 2.5 seconds forces 1Hz interrupt pulses to be output from the INTR pin for oscillation frequency measurement . (No pulse is output for less than 1.5 seconds.)
2 3
SCLK SIO
Shift clock input Serial input and output
The SCLK pin is used to input shift clock pulses to synchronize data input to, and output from, the SIO pin. The SIO pin inputs and outputs written or read data in synchronization with and output shift clock pulses from the SCLK pin. The SIO pin causes high impedance when the CE pin is held at the low level. After the CE pin is switched to the high level and the control bits and the address bits are input from the SIO, the SIO pin performs serial input and output operations
5 7 6
INTR OSCIN OSCOUT
Interrupt output Oscillation circuit input and output
The INTR pin outputs cyclic interrupt pulses to the CPU. This pin functions as an Nch open drain output even when the CE pin is held at the low level. These pins configure an oscillation circuit by connecting a 32.768 kHz crystal oscillator between the OSCIN and OSCOUT pins and by connecting a capacitor between the OSCIN and VSS pins. (Any other oscillation circuit components are built into the RS5C313.)
8 4
VDD VSS
Positive power supply input Negative power supply input The VDD pin is connected to a power supply and the VSS pin is connected to the ground.
3
RS5C313
ABSOLUTE MAXIMUM RATINGS
Symbol Item Conditions Ratings
(VSS=0V)
Unit
VDD VI VO1 VO2 PD Topt Tstg
Supply voltage Input voltage Output voltage1 Output voltage2 Maximum power consumption Ambient operating temperature Storage temperature SIO INTR Topt=25C
-0.3 to +7.0 -0.3 to +VDD+0.3 -0.3 to +VDD+0.3 -0.3 to +12 300 -30 to +80 -40 to +125
V V V V mW C C
ABSOLUTE MAXIMUM RATINGS
Absolute Maximum ratings are threshold limit values that must not be exceeded even for an instant under any conditions. Moreover, such values for any two items must not be reached simultaneously. Operation above these absolute maximum ratings may cause degradation or permanent damage to the device. These are stress ratings only and do not necessarily imply functional operation below these limits.
4
RS5C313
RECOMMENDED OPERATING CONDITIONS
(VSS=0V, Topt=-30 to +80C)
Symbol
Item
Conditions
MIN.
TYP.
MAX.
Unit
VDD VCLK fXT CG VPUP
Operating supply voltage Time Keeping supply voltage Oscillation frequency External oscillator capacitance Applied voltage at OFF CL value of crystal=6 to 8pF INTR
2.7 1.6
5.0
6.0 6.0
V V kHz
32.768 5 10 24 10
pF V
DC CHARACTERISTICS
Unless otherwise specified:VSS=0V, VDD=5V10%, Topt=-30 to +80C, oscillation frequency=32.768kHz (CL=6pF, R1=30k), CG=10pF
Symbol
Item
Pin name
Conditions
MIN.
TYP.
MAX.
Unit
VIH VIL IOH IOL1 IOL2 RDN IILK IOZ1 IOZ2 IDD1
"H" input voltage "L" input voltage "H" output current "L" output current Pull-down resistance Input leakage current Output off-state leakage current Power consumption 1
CE, SCLK, SIO CE, SCLK, SIO SIO SIO INTR CE SCLK SIO INTR VDD I/O=OPEN VDD=5.5V I/O=OPEN VI =VDD or VSS VO=VDD or VSS VO=10V VDD=3V VOH=VDD-0.5V VOL1=0.5V VOL2=0.4V
0.8VDD 0
VDD 0.2VDD -1
V V mA mA
1 2 45 -1 -2 -5 0.7 130 450 1 2
k A A
5 1.5 A
IDD2
Power consumption 2
VDD
2
A
CD
Internal oscillator capacitance
OSCOUT
10
pF
5
RS5C313
AC CHARACTERISTICS
VDD=5V10% Symbol Item MIN. MAX. MIN.
(VSS=0V, Topt=-30 to +80C, CL=50pF)
VDD=3V10% MAX.
VDD=5V20% MIN. MAX. Unit
tCES tCEH tCR tSCK tCKH tCKL tCKS tRE tRR tRZ tDS tDH
CE set-up time CE hold time CE recovery time SCLK clock cycle SCLK "H" clock time SCLK "L" clock time SCLK clock set-up time Data output start time (from Data output delay time (from Output floating time Input data set-up time Input data hold time of SCLK) of SCLK)
175 175 350 350 175 175 60 120 120 120 50 50
300 300 600 600 300 300 100 200 200 200 80 50
200 200 400 400 200 200 80 135 135 135 60 50
ns ns ns ns ns ns ns ns ns ns ns ns
TIMING CHART
CE
tCES tCKS tSCK tCKH tRE tCKL Read Data tDS tDH Write Data
tCEH
tCR
SCLK
tRR
tRZ
Read cycle
SIO
Write cycle
SIO
Input/output conditions VIH = 0.8 x VDD VIL = 0.2 x VDD VOH = 0.8 x VDD VOL = 0.2 x VDD
*) The ability that is fair in "H" or
"L" slanted line department
6
RS5C313
FUNCTIONAL DESCRIPTIONS
1. Addressing
Address A3 A2 A1 A0 Description Data*1 D3 D2 D1 D0
0 1 2 3 4 5 6 7 8 9 A B C D E F
0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1
0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
1-second counter 10-second counter 1-minute counter 10-minute counter 1-hour counter 10-hour counter Day-of-the-week counter Interrupt cycle register 1-day counter 10-day counter 1-month counter 10-month counter 1-year counter 10-year counter Control register Test register
S8 --*2 M8 -- H8 -- -- CT3 D8 -- MO8 -- Y8 Y80 CTFG --
S4 S40 M4 M40 H4 -- W4 CT2 D4 -- MO4 -- Y4 Y40 12/24 --
S2 S20 M2 M20 H2 P/A or H20 W2 CT1 D2 D20 MO2 -- Y2 Y20 WTEN/XSTP*3 --
S1 S10 M1 M10 H1 H10 W1 CT0 D1 D10 MO1 MO10 Y1 Y10 ADJ/BSY*4 TEST
*1) *2) *3) *4)
All the listed data can be read and written . The "--" mark indicates data which can be read only and set to "0" when read . The WTEN/XSTP bit of the control register is set to WTEN for write operation and XSTP for read operation. The ADJ/BSY bit of the control register is set to ADJ for write operation and BSY for read operation.
7
RS5C313
2. Register
2.1 Control Register (at Eh)
D3 CTFG CTFG D2 12/24 12/24 D1 WTEN XSTP D0 ADJ BSY (For write operation) (For read operation)
30-second Adjustment Bit
ADJ Description
0 1
Ordinary operation Second digit adjustment
Clock/Calendar Counter Busy-state Indication Bit
BSY Description
0 1
Ordinary operation Second digit carry or adjustment
Clock Counter Enable/Disable Setting Bit
WTEN Description
0 1
Disabling of 1-second digit carry for clock counter Enabling of 1-second digit carry for clock counter
Oscillator Halt Sensing Bit
XSTP Description
0 1
Ordinary oscillation Oscillator halt sensing
12/24-hour Time Display System Selection Bit
12/24 Description
0 1
12-hour time display system (separate for mornings and afternoons) 24-hour time display system
Interrupt Flag Bit
CTFG Description
0 1
INTR=H(Nch Open Drain). Enabling of write operation when the CT3 bit is set to 1. INTR=L (Nch Open Drain). Enabling of write operation when the CT3 bit is set to 1.
2.1-1 (ADJ)
When the ADJ bit is set to 1: (If the WTEN bit is 0, adjustment of second digits is started after the WTEN bit is set to 1.) 1) For second digits ranging from 00 to 29 seconds: Time counts smaller than seconds are reset to set second digits to "00". 2) For second digits ranging from 30 to 59 seconds: Time counts smaller than seconds are reset to set second digits to "00" and increment minute digits by 1. After the ADJ bit is set to 1, the BSY bit is set to 1 for the maximum duration of 122.1s.
8
RS5C313
2.1-2 (BSY)
When the BSY bit is 1, the clock and calendar counters are being updated. Consequently, write operation should be performed for the counters when the BSY bit is 0. Meanwhile, read operation is normally performed for the counters when the BSY bit is 0, but can be performed without checking the BSY bit as long as appropriate software is provided for preventing read errors(Refer to the item 11.3 Read Operation from Clock and Calendar Counters). The BSY bit is set to 1 in the following three cases:
(1) Adjustment of second digits by 30 seconds
MAX. 122.1s Setting of the ADJ bit to 1 Completion of second digit adjustment
(2) Second digit increment by 1 (Subject to 1-second digit carry when the WTEN bit is switched from 0 to 1) (3) Ordinary 1-second digit carry
MAX.91.6s Setting of the WTEN bit to 1 End of second digit increment by 1
91.6s End of second digit carry pulse
2.1-3 (WTEN)
The WTEN bit should be set to 0 to check that the BSY bit is 0 when performing read and write operations for the clock and calendar counters. For read operation, the WTEN bit may be left as 1 without checking the BSY bit as long as appropriate measures such as read repetition are provided for preventing read errors(Refer to the item 11.3 Read Operation from Clock and Calendar Counters). The WTEN bit should be set to 1 after completing read and write operations, or will automatically be set to 1 by switching the CE pin to the low level. If 1-second digit carry occurs when the WTEN bit is 0, a second digit increment by 1 occurs when the WTEN bit is set to 1.
Note
If the WTEN bit is 0 for 1/1024 second and more, second digit increment by 1 may not occur. (Refer to the item 11.3 Read Operation from Clock and Calendar Counters).
2.1-4 (XSTP)
The XSTP bit senses the ocilllator halt. When the CE pin is held at the low level, the XSTP bit is set to 1 once the crystal oscillator is stopped after initial power-on or supply voltage drop and left to be 1 after it is restarted. When the CE pin is held at the high level, the XSTP bit is left as it was when the CE pin was held at the low level without checking oscillation stop. As such, the XSTP bit can be used to validate clock and calendar count data after power-on or supply voltage drop. The XSTP bit is set to 0 when write operation is performed for the control register (at Eh) (during normal oscillation).
2.1-5 (12/24)
The 12/24 bit specifies time digit display in BCD code.
24-hour time display system 12-hour time display system 24-hour time display system 12-hour time display system
00 01 02 03 04 05 06 07 08 09 10 11
12(AM12) 01(AM 1) 02(AM 2) 03(AM 3) 04(AM 4) 05(AM 5) 06(AM 6) 07(AM 7) 08(AM 8) 09(AM 9) 10(AM10) 11(AM11)
12 13 14 15 16 17 18 19 20 21 22 23
32(PM12) 21(PM 1) 22(PM 2) 23(PM 3) 24(PM 4) 25(PM 5) 26(PM 6) 27(PM 7) 28(PM 8) 29(PM 9) 30(PM10) 31(PM11)
Either the 12-hour or 24-hour time display system should be selected before time setting (e.g. during initialization after power-on).
9
RS5C313
2.1-6 (CTFG)
The CTFG bit is set to 1 when interrupt pulses are output from the INTR pin held at the low level. There are two interrupt modes selectable: the pulse mode (when the CT3 bit is set to 0) and the level mode (when the CT3 bit is set to 1). The CTFG bit can be set only when the CT3 is set to 1. Setting the CTFG bit to 1 switches the INTR pin to the low level while setting the CTFG bit to 0 turns off the INTR pin.
Interrupt cycle register CT3 CT2 CT1 CT0 Outputs from INTR pin Remarks
0 0 0 0 1 1 1 1 1 1 1 1
**1 * * *
0 0 0 0 1 1 1 1
0 0 1 1 0 0 1 1 0 0 1 1
0 1 0 1 0 1 0 1 0 1 0 1
OFF ON 0.977ms 0.5s 1 second 10 seconds 1 minute 10 minutes 1 hour 1 day 1 week 1 month
Interrupt disabling Fixing INTR pin at low level Cycle: 0.977 ms (1/1024 Hz), Duty: 50% *2 Cycle: 0.5 s (1/2 Hz)*3 Every second*4
Every 10 seconds (For display of second digits: 00, 10, 20, 30, 40, and 50)*4
Every minute (00 second)*4 Every 10 minutes (00 second) (For display of minute digits: 00, 10, 20, 30, 40, and 50)*4 Every hour (00 minute and 00 second)*4 Every day (0 hour, 00 minute, and 00 second a.m.)*4 Every week (0 week, 0 hour, 00 minute, and 00 second a.m.)*4 Every month (1st day, 0 hour, 00 minute, and 00 second a.m.)*4
*1) *2)
The symbol " " in the above table indicates 0 or 1.
*
0.977ms
CTFG INTR
*3)
CTFG INTR
0.488ms
0.5s
*
4)
CTFG INTR
Interrupt (Second count-up)
Setting CTFG bit to 0 Interrupt (Second count-up)
10
RS5C313
2.2 Interrupt Cycle Register (at 7h)
D3 CT3 CT3 D2 CT2 CT2 D1 CT1 CT1 D0 CT0 CT0 (For write operation) (For read operation)
Bits for selecting the interrupt cycle and output mode at the INTR pin*1
*1)
(CT3 to CT0) The CT3 to CT0 bits are used to select the interrupt cycle and output mode at the INTR pin. There are two interrupt modes selectable: the pulse mode (when the CT3 bit is set to 0) and the level mode (when the CT3 bit is set to 1). The interrupt cycle and output mode at the INTR pin are shown in detail in the section on the CTFG bit in "2.1 Control Register (at Eh)".
2.3 Test Register (at Fh)
D3 D2 D1 D0 TEST 0 (For write operation) (For read operation)*1
*
0
*
0
*
0
Bit For Testing*2
TEST Description
0 1
Testing mode Ordinary operating mode
*1) *2)
The TEST bit is write-only and set to 0 when read. The TEST bit should be fixed at 1 for ordinary operation and will automatically be set to 1 when the CE pin is at the low level.
11
RS5C313
3. Counters
3.1 Clock Counter (at 0h to 5h)
D3 S8 D2 S4 S40 M4 M40 H4 D1 S2 S20 M2 M20 H2 P/A or H20 D0 S1 S10 M1 M10 H1 H10 ( read and write cycle) 1-second time digit (at 0h) (read and write cycle) 10-second time digit (at 1h) (read and write cycle) 1-minute time digit (at 2h) (read and write cycle) 10-minute time digit (at 3h) (read and write cycle) 1-hour time digit (read and write cycle) 10-hour time digit (at 4h) (at 5h)
*
M8
*
H8
*
*
1) The "*" mark in the above table indicates data which are set to 0 for read cycle and not set for write cycle. 2) Any carry to 1-second digits from the second counter is disabled when the WTEN bit (of the control register) is set to 0. 3) Time digit display ( BCD code): Second digits: Range from 00 to 59 and carried to minute digits when incremented from 59 to 00. Minute digits: Range from 00 to 59 and carried to hour digits when incremented from 59 to 00. Hour digits: Range as shown in the section on the 12/24 bit and carried to day and day-of-the-week. digits when incremented from 11 p.m. to 12 a.m. or 23 to 00. 4) Any registered imaginary time should be replaced with actual time as carrying to such registered imaginary time digits from lower-order ones cause the clock counter to malfunction.
3.2 Day-of-the-week Counter (at 6h)
D3 D2 W4 D1 W2 D0 W1 ( read and write cycle) Day-of-the-week counter
*
*
1) The " " mark in the above table indicates data which are set to 0 for read cycle and not set for write cycle. 2) Day-of-the-week digits are incremented by 1 when carried to 1-day digits. 3) Day-of-the-week digit display (incremented in septimal notation): (W4W2W1)=(000) (001) - - - - - - (110) (000) The relation between days of the week and day-of-the-week digits is user changeable (e.g. Sunday=000). 4) The (W4W2W1) should not be set to (111).
12
RS5C313
3.3 Calendar Counter (at 8h to Dh)
D3 D8 D2 D4 D1 D2 D20 MO2 D0 D1 D10 MO1 MO10 Y1 Y10 (read and write cycle) 1-day calendar digit (read and write cycle) 10-day calendar digit (at 8h) (at 9h)
*
MO8
*
MO4
(read and write cycle) 1-month calendar digit (at Ah) (read and write cycle) 10-month calendar digit (at Bh) (read and write cycle) 1-year calendar digit (read and write cycle) 10-year calendar digit (at Ch) (at Dh)
*
Y8 Y80
*
Y4 Y40
*
Y2 Y20
1) The " " mark in the above table indicates data which are set to 0 for read cycle and not set for write cycle. * 2) The automatic calendar function provides the following calendar digit displays in BCD code: Day digits: Range from 1 to 31 (for January, March, May, July, August, October, and December). Range from 1 to 30 (for April, June, September, and November). Range from 1 to 29 (for February in leap years). Range from 1 to 28 (for February in ordinary years). Carried to month digits when cycled to 1. Month digits: Range from 1 to 12 and carried to year digits when cycled to 1. Year digits: Range from 00 to 99 and counted as 00, 04, 08, - - - -- -, 92, and 96 in leap years. 3) Any registered imaginary time should be replaced with actual time as carrying to such registered imaginary time digits from lower-order ones cause the clock counter to malfunction.
13
RS5C313
USAGES
1. Read Data
The real-time clock becomes accessible by switching the CE pin from the low level to high level to enable interfacing with the CPU and then inputting setting data (control bits and address bits) to the SIO pin in synchronization with shift clock pulses from the SCLK pin. The input data are registered in synchronization with the falling edge of the SCLK. When the data is read, the read cycle shall be set by control bits. * Control bits R/W: Establishes the read mode when set to 1, and the write mode when set to 0. AD: Writes succeeding address bits (A3 to A0) to the address register when set to 1 with the DT bit set to 0 and performs no such write operation in any other case. DT: Writes data bits (D3 to D0) to the counter or register specified by the address register which has written just before when set to 1 with the R/W and AD bits set equally to 0 and performs no such write operation in any other case. A3 to A0: Inputs the bits MSB to LSB in the address table describing the functions.
* Address bits
1.1 Read Cycle Flow
1. The CE pin is switched from the low level to the high level. 2. Four control bits (with the first bit ignored) and four read address bits are input from the SIO pin. At this time, control bits R/W and AD are set equally to 1 while a control bit DT is set to 0. 3. The SIO pin enters the output mode at the rising edge of the shift clock pulse 2B from the SCLK pin while the four read bits (MSBLSB) at designated addresses are output at the rising edge of the shift clock pulse 5B (see the figure below). 4. Then, the SIO pin returns to the input mode at the rising edge of the shift clock pulse 1C. Afterwards control bits and address bits are input at the shift clock pulses 1C in the same manner as at the shift clock pulse 1A. 5. At the end of read cycle, the CE pin is switched from the high level to the low level (after tCEH from the falling edge of the eighth shift clock pulse from the SCLK pin). (Following on read cycle, write operation can be performed by setting control bits in the write mode at the shift clock pulse 1C and later with the CE pin held at the high level.)
CE
1A 2A 3A 4A 5A 6A 7A 8A 1B 2B 3B 4B 5B 6B 7B 8B 1C 2C 3C
SCLK Reading to shift register Setting of Shifting data SIO pin in output mode
A3 A2 A1 A0
Setting of SIO pin in input mode
R/W AD
Input to SIO pin
*
*
R/W AD
DT
(Hi-z)
Control bits Output from SIO pin (Hi-z) (Internal processing)
Address bits
--
--
--
D3
D2
D1
D0
(Hi-z) Read data
Setting of control bits
Writing to address register
*)
In the above figure, the " "mark indicates arbitrary data; the "--" mark indicates unknown data; * the " " mark indicates data which are available when the SIO pin is held at the high, low, or Hiz level ; and the diagonaliy shaded area indicates high or low.
14
RS5C313
2. Write Data
Writing data to the real-time clock requires inputting setting data (control bits and address bits) to the SIO pin and then establishing the write mode by using a control bit R/W in the same manner as in read operation.
*)
Control bits and address bits are described in the previous section on read cycle.
* Data bits
D3 to D0 : inputs writing data to the counter or the register describing the functions in order of MSB to LSB.
2.1 Write Cycle Flow
1. The CE pin is switched from the low level to the high level. 2. Four control bits (with the first bit ignored) and four write address bits are input from the SIO pin. At this time, control bits R/W and DT are set equally to 0 while a control bit AD is set to 1 (at the shift clock pulses 1A to 8A from the SCLK pin). 3. Four control bits and four bits of data to be written are input in the descending order of their significance. At this time, control bits R/W and AD are set equally to 0 while a control bit DT is set to 1 (at the shift clock pulses 1B to 8B from the SCLK pin). 4. When write cycle is continued, control bits and address bits are input at the shift clock pulse 1C and later in the same manner as at the shift clock pulse 1A. 5. At the end of write operation, control bits R/W, AD, and DT are set equally to 0 (at the falling edge of the fifth shift clock pulse and later from the SCLK pin) or the CE pin is switched from the high level to the low level (after
tCEH from the falling edge of the eighth shift clock pulse from the SCLK pin).
CE
1A 2A 3A 4A 5A 6A 7A 8A 1B 2B 3B 4B 5B 6B 7B 8B 1C 2C 3C
SCLK Reading from shift register
Input to SIO pin
*
*
R/W AD
DT
A3
A2
A1
A0
*
R/W AD
DT
D3
D2
D1
D0
*
R/W AD
Control bits Output from SIO pin
Address bits
Control bits
Data bits
(Hi-z)
Setting of control bits Writing to address register Setting of control bits
(Hi-z)
End of write operation
(Internal processing)
*)
In the above figure, the " " mark indicates arbitrary data; and the diagonally shaded area indicates the high or low level.
*
15
RS5C313
3. CE Pin
Shift clock pulses Address & Write data Read data Reading control bits Control bits
SCLK SIO
CE
1) Switching the CE pin to the high level enables both the SCLK and SIO pins, allowing data to be serially read from and written to the SIO pin in synchronization with shift clock pulses input from the SCLK pin. 2) Switching the CE pin to the low level or opening it disables both the SCLK and SIO pins, causing high impedance and resetting the internal interfacing circuits such as the shift register. 3) The CE pin should be held at the low level or open state when no access is made to the RS5C313. The CE pin incorporates a pull-down resistor. 4) During system power-down (being back-up battery powered), the low-level input of the CE pin should be brought as close as possible to the VSS level to minimize the loss of charge in the battery. 5) Holding the CE pin at the high level for more than 2.5 seconds mainly forces 1Hz interrupt pulses to be output from the INTR pin for oscillation frequency measurement. When the CE pin is held at the high level for less than 1.5 seconds, no pulse is output. 6) The CE pin should be held at the low level in order to enable oscillator halt sensing. Holding the CE pin at the high level, therefore, disables oscillator halt sensing, retaining the value of the XSTP (oscillator halt sensing) bit which exists immediately before the CE pin is switched to the high level.
Considerations When the power turns on from 0V, the CE pin should be set low or open once.
16
RS5C313
4. Configuration of Oscillating Circuit
VDD 8 OSCIN CG 32kHz RD 6 CD A OSCOUT
VDD
7 RF
Typical external device: X'tal : 32.768kHz (R1=30k) (CL=6pF to 8pF) CG=8pF to 20pF Standard values of internal devices: RF=15M (TYP.) RD=60k (TYP.) CD=10pF (TYP.)
VSS
The oscillation circuit is driven at a constant voltage of about 1.5 V relative to the VSS level. Consequently, it generates a waveform having a peak-to-peak amplitude of about 1.5 V on the positive side of the VSS level.
Considerations in Mounting Components Surrounding Oscillating Circuit 1) Mount the crystal oscillators and CG in the closest possible position to the IC. 2) Avoid laying any signal or power line close to the oscillation circuit (particularly in the area marked with "A " in the above figure). 3) Apply the highest possible insulation resistance between the OSCIN or OSCOUT pin and the PCB. 4) Avoid using any long parallel line to wire the OSCIN or OSCOUT pin. 5) Take extreme care not to cause condensation, which leads to various problems such as oscillation halt.
Other Relevant Considerations 1) When applying an external input of clock pulses (32.768 kHz) to the OSCIN pin: DC coupling - - - - - Prohibited due to mismatching input levels. AC coupling - - - - - Permissible except that unpredictable results may occur in oscillator halt sensing due to possible sensing errors caused by noises, etc. 2) Avoid using the oscillator output of the RS5C313 (from the OSCOUT pin) to drive any other IC for the purpose of ensuring stable oscillation.
17
RS5C313
5. Oscillator Halt Sensing
Oscillation Halt can be sensed by setting the XSTP (oscillator halt sensing) bit to 0 (after writing data to the control register) and then monitoring the XSTP bit. Upon oscillator halt sensing, the XSTP bit is switched from 0 to 1. This function can be applied to judge clock data validity.
XSTP
Power-on from 0V*1 Writing of data to Oscillation halt control register (in the presence of oscillation) Oscillation restart*2
*1) *2)
While the CE pin is held at the low level the XSTP bit is set to 1 upon power-on from 0 V. Note that any instantaneous power disconnection may cause operational failure. When the CE pin is held at the high level oscillation halt is not sensed and the value of the XSTP bit when the CE pin is held at the low level is retained. Once oscillation halt has been sensed, the XSTP bit is held at 1 even if oscillation is restarted.
Considerations in Use of XSTP Bit Ensure error-free oscillation halt sensing by preventing the following: 1) Instantaneous disconnection of VDD 2) Condensation on the crystal oscillator 3) Generation of noise on the PCB in the crystal oscillator 4) Application of voltage exceeding prescribed maximum ratings to the individual pins of the IC
6. Typical Power Supply Circuit
1) Connect the capacitance of the oscillation circuit to the VSS pin.
System supply voltage RS5C313
2) Mount the high- and low-frequency by-pass capacitors in parallel and very close to the RS5C313. 3) Connect the pull-up resistor of the INTR pin to two different posi-
A
INTR
tions depending on whether the resistor is in use during battery back-up. * When not in use during battery back-up - - - - - Position A in the left figure * When in use during battery back-up - - - - - Position B in the left figure 4) Timing of power supply on / off and CE terminal refer to lower part plan.
C System supply voltage D Battery voltage 0V CE 0.2VDD 0.2VDD 0.2VDD E
B
OSCIN OSCOUT VDD
VSS
VDD
MIN. 0s
MIN. 0s
MIN. 0s
C,D,E : The lower limit voltage for CPU operation
18
RS5C313
7. Oscillation Frequency Adjustment
7.1 Oscillation Frequency Measurement
VDD OSCIN 32kHz CG OSCOUT INTR CE VSS Frequency counter +5V or +3V
1) When switch the CE pin to the high level after low level or open state, a 1-Hz interrupt pulse is output from the INTR pin about 2.5 seconds later. Measure this interrupt pulse by using a frequency counter 2) Ensure that the frequency counter has more than six digits (on the order of 1 ppm). 3) Place the CG between the OSCIN pin and the VSS level and pull up the INTR pin output to the VDD .
7.2 Oscillation Frequency Adjustment
Select crystal oscillator (For fixed capacitance) Fix CG. Change CL value of crystal. Optimize CG. NG OK End
*1 *3 *
3
(For variable capacitance) Fix the capacitance of CG.
*
2
Change the CL value of crystal. NG
Optimize central variable capacitance value OK
Make fine frequency adjustment with variable capacitance. End
To ensure that the crystal is matched to the IC, inquire its crystal supplier about its CL (load capacitance) and R1 (equivalent series resistance) values. It is recommended that the crystal should have the CL value range of 6 to 8pF and the typical R1 value of 30k ohms. 2) To allow for the possible effects of floating capacitance, select the optimum capacitance of the CG on the mounted PCB. The standard and recom* mendable capacitance values of the CG range from 5 to 24pF and 8 to 20pF, respectively. When you need to change the frequency to get higher accuracy, change the CL value of the crystal. *3) Collate the central variable capacitance value of the CG with its oscillation frequency by adjusting the angle of rotation of the variable capacitance of the CG in such a manner that the actual variable capacitance value is slightly smaller than the central variable capacitance value. (It is recommended that the central variable capacitance value should be slightly less than one half of the actual variable capacitance value because the smaller is variable capacitance, the greater are fluctuations in oscillation frequency.) In the case of an excessive deviation of the oscillation frequency from its required value, change the CL value of the crystal.
*1)
19
RS5C313
After adjustment, oscillation frequency is subject to fluctuations of an ambient temperature and supply voltage. See "10. Typical Characteristic Measurements".
Note Any rise or fall in ambient temperature from its reference value ranging from 20 to 25 degrees Celsius causes a time delay for a 32kHz crystal oscillator. It is recommendable, therefore, to set slightly high oscillation frequency at room temperature.
8. Interrupt Operation
The INTR pin output, the interrupt cycle register, and the CTFG bit can be used to interrupt the CPU in a certain cycle. (The INTR pin functions as an Nch open drain output.)
8.1 Selection of Interrupt Cycle
The interrupt cycle register can be used to select either one of two interrupt output modes: the pulse mode (when the CT3 bit is set to 0) and the level mode (when the CT3 bit is set to 1).
Interrupt cycle register CT3 CT2 CT1 CT0 INTR pin output Remarks
0 0 0 0 1 1 1 1 1 1 1 1
**1 * * *
0 0 0 0 1 1 1 1
0 0 1 1 0 0 1 1 0 0 1 1
0 1 0 1 0 1 0 1 0 1 0 1
OFF ON 0.977ms 0.5s 1 second 10 seconds 1 minute 10 minutes 1 hour 1 day 1 week 1 month
Interrupt halt Fixing the INTR pin at the low level Cycle: 0.977ms (1/1024Hz) Duty: 50% Cycle: 0.5s (1/2Hz) Every second Every 10 seconds (For display of second digits: 00, 10, 20, 30, 40, and 50) Every minute (00 second)
Every 10 minutes (00 second) (For display of minute digits: 00, 10, 20, 30, 40, and 50)
Every hour (00 minute and 00 second) Every day (0 hour, 00 minute, and 00 second a.m.) Every week (0 week, 0 hour, 00 minute, and 00 second a.m.) Every month (1st day, 0 hour, 00 minute, and 00 second a.m.)
*1)
The symbol " " in the above table indicates 0 or 1.
*
20
RS5C313
8.2 Pulse Mode Interrupt
When the CT3 bit is set to 0 and provides four interrupt cycles, off, on, 1024 Hz, and 2 Hz can be selected. The CTFG bit cannot be set because it is used for output monitoring.
T1
CTFG INTR
0.488ms
1024Hz : T1=0.977ms 2Hz : T1=500ms
8.3 Level Mode Interrupt
When the CT3 bit is set to 1, clock-interlocked cycles in increments of 1 second to 1 month can be selected. The CTFG bit can be written; writing the CTFG bit switches the INTR pin to the low level while writing 0 to the CTFG bit turns off the INTR pin.
CTFG INTR
Interrupt (Second count-up)
Interrupt Writing 0 to CTFG bit (Second count-up)
9. Typical Application
System supply voltage System supply voltage B VCC INTR CE SCLK SIO VSS VSS OSCOUT VDD OSCIN A
CPU
RS5C313
1) 2) 3)
Connect the capacitance of the oscillation circuit to the VSS pin. Mount the high- and low-frequency by-pass capacitors in parallel and very close to the RS5C313. Connect the pull-up resistor of the INTR pin to two different positions depending on whether the resistor is in use during battery back-up. When not in use during battery back-up - - - - - Position A in the above figure When in use during battery back-up - - - - - - -- Position B in the above figure
21
RS5C313
10. Typical Characteristic Measurements
VDD CG VDD A X'tal OSCOUT OSCIN
CG=10pF X'tal : R1=30k, CL=6pF Topt=25C Input pin : VDD or VSS Output pin : Open
VSS INTR Frequency counter
10.1 Standby Current vs. CG (VDD=3V)
2.0 Standby Current IDD (A) Topt=25C
10.2 Standby Current vs. VDD(CG=10pF)
2.0 Standby Current IDD (A) Topt=25C
1.0
VDD=3V
1.0
CG=10pF
0.0
0.0 0 10 CG (pF) 20 30
0
2 VDD (V)
4
6
10.3 Operational Current vs. SCLK Frequency
1 Operational Current IOPR (mA) Topt=25C
10.4 Standby Current vs. Temperature (VDD=3V, 5V)
2 Standby Current IDD (A) CG=10pF
0.1
1
VDD=5V VDD=3V
VDD=5V
0.01
VDD=3V
0.001 0.01
1 0.1 SCLK Frequency (MHz)
10
0 -40 -20
20 40 60 80 0 Temperature Topt (C)
100
22
RS5C313
10.5 Oscillation Frequency Deviation vs. CG (f0: CG=10pF reference)
Oscillation Frequency Deviation f/f0 (ppm) 80 60 40 20 0 -20 -40 VDD=3V, Topt=25C
10.6 Oscillation Frequency Deviation vs. VDD (f0: VDD=4V reference)
1 0 -1 -2 -3 -4 CG=10pF, Topt=25C
Oscillation Frequency Deviation f/f0 (ppm)
0
10
20 CG (pF)
30
0
1
2
4 3 VDD (V)
5
6
10.7 Oscillation Frequency Deviation vs. Temperature 10.8 Oscillation Start Time vs. VDD (f0: Topt=25C reference)
10 Oscillation Frequency Deviation f/f0 (ppm) 0 -10 -20 -30 -40 -50 -60 -70 -80 -40 -20 0 20 40 60 80 100 Temperature Topt (C) 0.0 0 Oscillation Start Time (s) VDD=3V, CG=10pF 1.0 Topt=25C
0.5
CG=20pF CG=10pF
1
2
3 4 VDD (V)
5
6
10.9 VDS vs. IDS for Nch Open Drain Output
50 Nch Open Drain Output IDS (mA) 40 30
VDD=5V
Topt=25C
20
VDD=3V
10 0 0.0
0.5
1.0 VDS (V)
1.5
2.0
23
RS5C313
11. Typical Software-based Operations
11.1 Initialization upon Power-on
Start
*1) *2)
Switch the CE pin to the low level immediately after power-on. When not making oscillation halt sensing (data validity), the XSTP bit need not be checked. Turn off the INTR pin, whose output is uncertain at power-on. Write to control register 3h for 12-hour format or 7h for 24-hour format. Set the ADJ bit to 1 for checking oscillaiton. It takes 0.1-2 seconds to be set the BSY bit to 0 from oscillation starting upon power-on from 0V. Provide an exit from an oscillation start loop to prepare for oscillation failure. Set the XSTP bit to 0 by writing data to the control register. 0h for the 12-hour time display system. 4h for the 24-hour time display system.
Power-on YES XSTP=0? No Interrupt cycle register0h Control register3h, 7h
*1 *2 *3 *4
NO
*3) *4) *5) *6)
BSY=0? YES
*6
*5
Wait or other operations.
When using the XSTP bit Ensure stable oscillation by preventing the following: 1) Condensation on the crystal oscillator 2) Instantaneous disconnection of power 3) Generation of clock noises, etc. in the crystal oscillator 4) Charge of voltage exceeding prescribed maximum ratings to the individual pins of the IC
Control register0h, 4h Set clock and calendar counters and interrupt cycles.
11.2 Write Operation to Clock and Calendar Counters
*1)
CE=H
*1
*2)
After switching the CE pin to the high level, hold it at the high level until any subsequent operation requires switching it to the low level. (Note that switching the CE pin to the low level sets the WTEN bit to 1.) Write 0h for the 12-hour format or 4h for the 24-hour time display system. The BSY bit is held at 1 for a maximum duration of 122.1 us. Switch the CE pin to the low level to set the WTEN bit to 1. During write operation to the clock and calendar counters, one 1-second digit carry causes a 1-second increment while two 1-second digit carries also cause only a 1-second increment, which, in turn, causes a time delay.
Control register0h, 4h BSY=0? YES Write to clock and calendar counters.
*2
NO
*3) *4)
CE=L Wait or other operations.
*3
*4
CE=L
24
RS5C313
11.3 Read Operation from Clock and Calendar Counters 11.3-1 11.3-2
CE=H Control register 0h, 4h BSY=0? YES Read from clock and calendar counters.
*1 *2
NO
Read 1-second digit of clock counter. Read from clock and calendar counters. Again read 1-second digit of clock counter.
*5
CE=L Wait or other operations.
*5
*3
*4
CE=L
NO
Two1-second digit readings match? YES
*5
Note
Read data as described in 11.3-2 or 11.3-3 when it takes (1/1024) sec or more to set the WTEN bit from 0 to 1 (CE=L), the read operation described in 11.3-1 is prohibited as such a case.
11.3-3
*1)
Interrupt to CPU CTFG=1? YES
After switching the CE pin to the high level, hold it at the high level until any subsequent operation requires switching it to the low level. (Note that switching the CE pin to the low level sets the WTEN bit to 1.) Write 0h for the 12-hour format or 4h for the 24-hour time display system. The BSY bit is held at 1 for a maximum duration of 122.1 us. Switch the CE pin to the low level to set the WTEN bit to 1. During write operation to the clock and calendar counters, one 1-second digit carry causes a 1-second increment while two 1-second digit carries also cause only a 1-second increment, which, in turn, causes a time delay. When needing any higher-order digits than the minute digits, replace second digits with minute digits. (Reading LSD one of the required digits twice.) Select the level mode as an interrupt mode by setting the CT3 bit to 1. Write 2h for the 12-hour format or 6h for the 24-hour format. Complete read operation within an interrupt cycle after interrupt generation (e.g. within 1 second).
*6
NO
*2) *3) *4)
Interrupt operation from any other IC
Control register 2h, 6h Read from clock calendar counter
*7 *8
*5) *6) *7) *8)
25
RS5C313
11.4 Second-digit Adjustment by 30 seconds
Control register 3h, 7h
*1)
*
1
Write 3h for the 12-hour format or 7h for the 24-hour format and then set the ADJ bit to 1. (The BSY bit is held at 1 for a maximum duration of 122.1s after the ADJ bit is set to 1.)
11.5 Oscillation Start Judgment
*2)
Power-on
The XSTP bit is set to 1 upon power-on from 0V. It takes approximately 0.1 to 2 seconds to start oscillation. Provide an exit from an oscillation start loop to prepare for oscillation failure. Write 2h for the 12-hour format or 6h for the 24-hour format.
*3) *4)
YES
XSTP=0?
*2
4
*3
Wait or other operations
NO * Control register 2h, 6h
When using the XSTP bit Ensure stable oscillation by preventing the following: 1) Condensation on the crystal oscillator 2) Instantaneous disconnection of power
Oscillation start
3) Generation of clock noises, etc. in the crystal oscillator 4) Charge of voltage exceeding prescribed maximum ratings to the individual pins of the IC
11.6 Interrupt Operation (a) Cyclic Interrupt Operation (Every 1 Second to 1 Month)
*5)
Set interrupt cycle register
Set the interrupt cycle register to the level mode by setting the CT3 bit to 1. Write 2h for the 12-hour format or 6h for the 24-hour format.
*5
*6)
Interrupt to CPU CTFG=1? YES NO
Control register 2h, 6h
*6
Interrupt operation from any other IC
Cyclic interrupt operation
26
RS5C313
(b) Daily Time (Hour or Minute) Alarm Operation*1
*1)
Interrupt cycle register h
In this typical operation, alarm time is stored in the CPU and collated with clock time through interrupt operation. Initially set address h to Ch (every 1 hour) and change it in the following sequence for every matching of clock counter readings in Ch Bh Ah (9h 8h) Every Every Every (Every Every) 1 hour 10 mins. 1 min. (10 secs. 1 sec.) In this manner, change the settings of the interrupt cycle register. Write 2h for the 12-hour format or 6h for the 24-hour format. Collate alarm time with clock time through interrupt operation. Interrupt Setting Time Digit for Collation Ch 10-hour and 1-hour digits Bh 10-minute digit (10-hour and 1-hour digits) Ah 1-minute digit (10-hour, 1-hour, and 10-minute digits) (9h) 10-second digit (10-hour digit to 1-minute digit) (8h) 1-second digit (10-hour digit to 10-second digit)
*2
*2)
Interrupt to CPU NO
CTFG=1? YES
*3) *4)
Control register 2h, 6h
*3
Interrupt operatin from any other IC
Read from clock counter
Readings match? YES
*4
NO
Note In the above typical operation, alarm time (hour and minute) is collated with clock time by making interrupt operation a maximum of 37 times per day as shown by the following calculation: 23(1-hour digit)+5(10-minute digit)+9(1-minute digit)=37 times In this connection, a total current consumption increase resulting from interrupt operation can also be calculated as follows: Assuming, for example, that interrupt operation to the CPU takes 50 ms and consumes 10mA of current, an average current consumption increase resulting from interrupt operation can be calculated as follows: (50 msx 10mAx 37 times) / (60 seconds x60 minutes x 24 hours)=0.21A Counting in a standard current consumption of about 0.91A when the RS5C313 is set to 3V, a total current consumption can be calculated at about 1.1A.
27
RS5C313
PACKAGE DIMENSIONS (Unit:mm)
* 8pin SSOP (0.65mm pitch)
3.50.3
8 5
0 to 10
4.40.2
6.40.3
1
4
0.65 0.775TYP. 1.150.1
+0.1 0.15 -0.05
0.1 0.220.1
0.15
0.10.1
M
TAPING SPECIFICATION (Unit:mm)
The RS5C313 has one designated taping direction. "RS5C313-E2".
4.00.1 2.00.05
1.750.1
The product designation for the taping components is
0.3
+0.1 o1.5 -0
5.50.05
6.7 2.7 MAX. 8.00.1
User Direction of Feed.
28
3.9
12.00.3
0.50.3
RICOH COMPANY, LTD. ELECTRONIC DEVICES DIVISION
HEADQUARTERS 13-1, Himemuro-cho, Ikeda City, Osaka 563-8501, JAPAN Phone +81-727-53-6003 Fax +81-727-53-2120 YOKOHAMA OFFICE (International Sales) 3-2-3, Shin-Yokohama, Kohoku-ku, Yokohama City, Kanagawa 222-8530, JAPAN Phone +81-45-477-1697 Fax +81-45-477-1694 * 1695 http://www.ricoh.co.jp/LSI/english/
RICOH CORPORATION ELECTRONIC DEVICES DIVISION
SAN JOSE OFFICE 1996 Lundy Avenue, San Jose, CA 95131, U.S.A. Phone +1-408-944-3306 Fax +1-408-432-8375 http://www.ricoh-usa.com/semicond.htm

▲Up To Search▲

Price & Availability of RS5C313

	To Download RS5C313 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .